IEC 60092-504:2001 pdf Electrical installations in ships – Part 504: Special features – Control and instrumentation
1 Scope
This part of IEC 60092 deals with electrical, electronic and programmable equipment intended
for control, monitoring, alarm and protection systems for use in ships.
2 Normative references
The following normative documents contain provisions which, through reference in this text,
constitute provisions of this part of IEC 60092. For dated references, subsequent amendments
to, or revisions of, any of these publications do not apply. However, parties to agreements
based on this part of IEC 60092 are encouraged to investigate the possibility of applying the
most recent editions of the normative documents indicated below. For undated references, the
latest edition of the normative document referred to applies. Members of IEC and ISO maintain
registers of currently valid International Standards.
IEC 60050 (all parts), International Electrotechnical Vocabulary (IEV)
IEC 60068-2-1 , Environmental testing – Part 2: Tests – Tests A: Cold
IEC 60068-2-2, Environmental testing – Part 2: Tests – Tests B: Dry heat
IEC 60068-2-6, Environmental testing – Part 2: Tests – Tests Fc: Vibration (sinusoidal)
IEC 60068-2-30, Environmental testing – Part 2: Tests – Tests Db and guidance: Damp heat,
cyclic (1 2 + 1 2-hour cycle)
IEC 60068-2-52, Environmental testing – Part 2: Tests – Tests Kb: Salt mist, cyclic (sodium
chloride solution)
IEC 60092 (all parts), Electrical installations in ships
IEC 60092-1 01 , Electrical installations in ships – Part 1 01 : Definitions and general
requirements
IEC 60092-201 , Electrical installations in ships – Part 201 : System design – General
IEC 60092-202, Electrical installations in ships – Part 202: System design – Protection
IEC 60092-204, Electrical installations in ships – Part 204: System design – Electric and
electrohydraulic steering gear
IEC 60092-302, Electrical installations in ships – Part 302: Low voltage switchgear and
controlgear assemblies
IEC 60092-375, Electrical installations in ships. Shipboard telecommunication cables and radio-
frequency cables. General instrumentation, control and communication cables
IEC 60092-376, Electrical installations in ships – Part 376: Shipboard multicore cables for
control circuits
IEC 60092-401 , Electrical installations in ships – Part 401 : Installation and test of completed
installation
IEC 60092-501 , Electrical installations in ships – Part 501 : Special features – Electric
propulsion plant
IEC 60092-502, Electrical installations in ships – Part 502: Tankers – Special features
IEC 60447, Man-machine interface (MMI) – Actuating principles
IEC 60529, Degrees of protection provided by enclosures (IP Code)
IEC 60533, Electrical and electronic installations in ships – Electromagnetic compatibility
IEC 60945, Maritime navigation and radiocommunication equipment and systems – General
requirements – Methods of testing and required test results
IEC 61 000-4-2, Electromagnetic compatibility (EMC) – Part 4: Testing and measurement
techniques – Section 2: Electrostatic discharge immunity test. Basic EMC Publication
IEC 61 000-4-3, Electromagnetic compatibility (EMC) – Part 4: Testing and measurement
techniques – Section 3: Radiated, radio-frequency, electromagnetic field immunity test
IEC 61 000-4-4, Electromagnetic compatibility (EMC) – Part 4: Testing and measurement
techniques – Section 4: Electrical fast transient/burst immunity test. Basic EMC Publication
IEC 61 000-4-5, Electromagnetic compatibility (EMC) – Part 4: Testing and measurement
techniques – Section 5: Surge immunity test
IEC 61 000-4-6, Electromagnetic compatibility (EMC) – Part 4: Testing and measurement
techniques – Section 6: Immunity to conducted disturbances, induced by radio-frequency fields
IEC 61 000-4-1 1 , Electromagnetic compatibility (EMC) – Part 4: Testing and measuring
techniques – Section 1 1 : Voltage dips, short interruptions and voltage variations immunity tests
CISPR 1 6-1 , Specification for radio disturbance and immunity measuring apparatus and
methods – Part 1 : Radio disturbance and immunity measuring apparatus
CISPR 1 6-2, Specification for radio disturbance and immunity measuring apparatus and
methods – Part 2: Methods of measurement of disturbances and immunity
IMO Assembly Resolution A.830 (1 9)1 995, Code on Alarms and Indicators 1
NOTE Other informative IMO documents are referenced within the text of this standard.
3 Definitions
For the purposes of this part of IEC 60092, the following definitions, having special application
to the control, monitoring, alarm and protection equipment, apply. For definitions of general and
more particular terms, reference is made to IEC 60050 (IEV) and other normative documents.
3.1 accuracy
quality which characterizes the closeness of a measured value to the corresponding true value
3.2 alarm functions
functions intended to alert relevant personnel, by visual and audible means, in the event of any
condition requiring their attention
IEC 60092-504:2001 pdf Electrical installations in ships – Part 504: Special features – Control and instrumentation
