IEC 60130-9:2011 pdf Connectors for frequencies below 3 MHz – Part 9: Circular connectors for radio and associated sound equipment
1 Scope
This part of IEC 601 30 relates to circular connectors for radio and associated sound
equipment.
NOTE IEC 61 076-2-1 06 specifies connectors with a similar mating interface for connectors M1 6×0,75 with screw-locking and degree of protection IP40 or IP65/IP67 and with M1 6×0,75 screw-locking accessory. As the IEC 601 30-9 connector styles mating with the corresponding ones of IEC 61 076-2-1 06 do not have a locking mechanism specified they are therefore not appropriate for industrial process measurement and control equipment.
Users of this IEC 601 30-9 standard should be aware that some of the IEC 61 076-2-1 06 styles could be mated but not locked to some connector styles of this IEC 601 30-9 standard.
2 Normative references
The following referenced documents are indispensable for the application of this document.
For dated references, only the edition cited applies. For undated references, the latest edition
of the referenced document (including any amendments) applies.
IEC 60068-1 : 1 988, Environmental testing – Part 1: General and guidance
Amendment 1 (1 992)
IEC 6051 2 (all parts), Connectors for electronic equipment – Basic testing procedures and
measuring methods
IEC 6051 2-1 -1 , Connectors for electornic equipment – Tests and measurements – Part 1-1:
General examination – Test 1a: Visual examination
IEC 6051 2-1 -2, Connectors for electronic equipment – Tests and measurements – Part 1-
2:General examination – Test 1b: Examination of dimension and mass
IEC 6051 2-2-1 , Connectors for electronic equipment – Tests and measurements –Part 2-
1:Electronic continuity and contact resistance tests – Test 2a: Contact resistance – Millivolt
level method
IEC 6051 2-3-1 , Connectors for electronic equipment – Tests and measurements –Part 3-1:
Insulation tests – Test 3a: Insulation resistance
IEC 6051 2-4-1 , Connectors for electronic equipment – Tests and measurements –Part 4-1:
Voltage stress tests – Test 4a: Voltage proof
IEC 6051 2-7-1 , Connectors for electronic equipment – Tests and measurements – Part 7-1:
Impact tests (free connectors) – Test 7a: Free fall (repeated)
IEC 6051 2-7-2, Connectors for electronic equipment – Tests and measurements – Part 7-2:
Impact tests (free components) – Test 7b: Mechanical strength impacts and measurements
IEC 6051 2-9-1 , Connectors for electronic equipment – Tests and measurements – Part 9-1:
Endurance tests – Test 9a: Mechanical operation
IEC 6051 2-1 1 -1 , Electromechanical components for electronic equipment – Basic testing
procedures and measuring methods – Part 11 – Section 1: Test 11a – Climatic sequence
IEC 6051 2-1 1 -3, Connectors for electronic equipment – Tests and measurements – Part 11-3:
Climatic tests – Test 11c: Damp heat, steady state
IEC 6051 2-1 1 -9, Connectors for electronic equipment – Tests and measurements – Part 11-9:
Climatic tests – Test 11i: Dry heat
IEC 6051 2-1 1 -1 0, Connectors for electronic equipment – Tests and measurements –
Part 11-10: Climatic tests – Test 11j: Cold
IEC 6051 2-1 1 -1 2, Connectors for electronic equipment – Tests and measurements –
Part 11-12: Climatic tests – Test 11m: Damp heat, cyclic
IEC 6051 2-1 3-2, Connectors for electronic equipment – Tests and measurements – Part 13-2:
Mechanical operation tests – Test 13b: Insertion and withdrawal forces
IEC 6051 2-1 6-5, Connectors for electronic equipment – Tests and measurements – Part 16-5:
Mechanical tests on contacts and terminations – Test 16e: Gauge retention force (resilient
contacts)
IEC 6051 2-1 7-1 , Connectors for electronic equipment – Tests and measurements – Part 17-1:
Cable clamping tests – Test 17a: Cable clamp robustness
IEC 6051 2-1 7-2, Connectors for electronic equipment – Tests and measurements – Part 17-2:
Cable clamping tests – Test 17b: Cable clamp resistance to cable rotation 2
IEC 6051 2-1 7-3, Connectors for electronic equipment – Tests and measurements – Part 17-3:
Cable clamping tests – Test 17c: Cable clamp resistance to cable pull (tensile)
IEC 6051 2-1 7-4, Connectors for electronic equipment – Tests and measurements – Part 17-4:
Cable clamping tests – Test 17d: Cable clamp resistance to cable Torsion
IEC 61 076-2-1 06, Connectors for electronic equipment – Product requirements – Part 2-106:
Circular connectors – Detail specification for connectors M 16 x 0,75 with screw-locking and
degree of protection IP40 or IP65/67 3
ISO 1 302, Geometrical Product Specifications (GPS) – Indication of surface texture in
technical product documentation
IEC 60130-9:2011 pdf Connectors for frequencies below 3 MHz – Part 9: Circular connectors for radio and associated sound equipment
